Irrigation pull ring lock-nut plug-manufacture,factory,supplier from China

This product is used when the drip irrigation system uses tape as the main pipeline. The branch water source, the main pipeline (soft belt) is connected with the drip irrigation belt, so that the water in the main pipeline (soft belt) flows into the drip irrigation belt separately.Use a punching machine (diameter 14mm) to make holes on the side of the soft water belt, then screw the tee into the hole of the soft water belt, tighten the nut to fix the bypass on the soft water belt, and connect the soft water belt to the other side of the drip irrigation belt.

Commands for use: Mainly used for capillary head give up manage (the right give up of the pull ring is hooked up to a 16mm drip tape, that is fixed through the pull ring; the left give up is hooked up to the water shipping most important pipe, which may be used for pe pipes (wall thickness more than 1mm), water transport tape or use with matching rubber bands , connect to pvc pipe.)Product introduction: the pull-ring pass switch is a generally used drip irrigation transfer.

1 Automatic irrigation       This technology was invented by the French National Institute of Agronomy. They developed an automatic irrigation device, that is, in the fruit branch and other parts, placed some special "tentacles" to test the crop of subtle changes.

FeaturesColor: As the pix shown.Material: ABS, plastic.Premium quality - 3 arm + ABS plastic rotary garden sprinkler with Ground Rod.Effective water sprinkler irrigation machine - patented layout of water-saving tool may be centered to keep water maximum with the aid of using adjusting the water density, length and scope.Easy use - join water joint to the connector and tap.Long spray distance - as much as 26ft-32.8ft distance with worldwide general pipes.Different spray direction - direct or forty five degree.Spraying distance: upward 2.5-3m, lateral 4-5m Connection length: half of Inch M

I. Composition of the microirrigation systemThe micro-irrigation system is composed of water source, front hub, water transmission and distribution pipe network, irrigation device, flow rate, pressure control parts and measuring instrument.1. Water sourceRivers, channels, lakes, reservoirs, wells and springs can be used as microirrigation water sources, and their water quality should meet the requirements of microirrigation.2.

Drip irrigation pipe is an important irrigator in drip irrigation system. According to the water demand of plants, through the low-pressure pipeline system and the irrigator installed on the capillary, the water and the nutrients required by the plants are dripped into the plants evenly and slowly. in the root zone soil.In particular, most of the landscaping plants are laid with a special drip irrigation pipe, and the drip irrigation pipe includes a pipe body and drip holes evenly distributed on the pipe body.

1. The effective utilization rate of water is high. Under the condition of drip irrigation, the irrigation water wets part of the soil surface, which can effectively reduce the ineffective evaporation of soil water. At the same time, because drip irrigation only moistens the soil near the roots of the crops, and the soil moisture content in other areas is low, it can prevent the growth of weeds. Third, the drip irrigation system does not generate ground runoff, and it is easy to grasp the precise watering depth, which is very water-saving.2.

Water is the source of all things. Without water, there is no life. Plant growth is also indispensable for the nourishment of water. Reasonable use of water resources can make fruit trees grow stronger, increase fruit tree yields, and improve fruit trees' annual yield and longevity. To exert the good influence of water on fruit trees, timely irrigation and drainage must be carried out to meet the growth and development needs of fruit trees.The water requirements of fruit trees are as follows:Plant water demand includes two aspects: physiological water demand and ecological water demand.

Features of sheet type drip irrigation belt　1、Integrated flat drip head drip irrigation belt is an integrated drip irrigation belt with flat-shaped drip head set on the inner wall of the pipe belt, which is widely used in greenhouse greenhouses and irrigation of cash crops in large fields. 　　2、The drip head is integrated with the pipe belt, easy to install and use, low cost and low investment. 　　3、Drip head has self-filtering window, good anti-clogging performance. 　　4、Using labyrinth flow channel, with a certain pressure compensation effect.

Drip irrigation belt is the core product of drip irrigation system and plays a decisive role in the operation effect of drip irrigation system. It is praised as an efficient water-saving equipment in arid and water-deficient areas, which can effectively improve the utilization rate of water and fertilizer and achieve rational planting of water saving and energy saving. Drip irrigation belt is to use plastic pipes to pass water (liquid fertilizer or pesticide, etc.) through a capillary tube with a diameter of about 16mm.

With the adjustment of planting structure, improving the quality of wheat has become the theme of wheat production. Wheat quality is affected by a variety of factors such as variety, environment, ecology and cultivation measures, there are various ways to improve the quality of wheat, in addition to the selection of high-quality varieties, through some cultivation and drip irrigation measures can also significantly improve the quality of wheat.

What Is Drip Irrigation?Drip irrigation is the exercise of applying small amounts of water and fertilizer uniformly across a specific location.  the water and fertilizer are delivered at once to the crop root sector, eliminating runoff, evaporation, and drift. A nicely designed and managed drip irrigation device offers manufacturers the first-class uniformity and application performance to be had, consequently saving them time, electricity, and water, all while maximizing yields.